| |
General Questions
1) What are the features of the VideoAFM™?
· Video rate operation, 1000 times faster than conventional AFM.
25 frames per second at 128 x 128 pixels.
15 frames per second at 256 x 256 pixels.
· Air and liquid operation.
· Resolution comparable to conventional AFM (contact mode).
· Operates in conjunctionwith 3rd party conventional AFM.
· Very simple non-invasive installation.
· Can image in high vibration environment.
<< back to top >>
2) What are the main components in a VideoAFM™ system?
· Workstation
· High-speed scan head.
· Microscanners.
· Cantilevers (specific to the VideoAFM™).
See specification sheet for more details.
<< back to top >>
3) How fast is the VideoAFM™
256 x 256 pixel images are generated at 15 frames per second.
128 x 128 pixel images are generated at 25 frames per second.
<< back to top >>
4) What is the maximum XY scan area?
Air operation: 3um x 3um.
Liquid operation: 1um x 1um.
<< back to top >>
5) What is the maximum Z scan range?
Typically, corrugations up to 100nm in air and 25nm in liquid, dependent on
spatial frequency.
<< back to top >>
6) What is the XY resolution?
The resolution is comparable to conventional contact mode AFM imaging -
approximately 10 nm (tip, sample and host AFM dependant).
<< back to top >>
7) What is the Z resolution?
The Z resolution <1nm, tip, sample and host AFM dependent.
<< back to top >>
8) Which microscopes are compatible with the VideoAFM™?
The VideoAFM™ is compatible with the vast majority of commercially available
atomic force microscopes.
Please contact your sales representative for further information.
<< back to top >>
9) How long does it take to swap between conventional AFM and VideoAFM™ imaging?
The interface with the conventional AFM is quick and simple and it takes no more
than a few minutes to attach the VideoAFM™. It monitors a small number of signals
from the base microscope, which are routed directly into the back of the
controller. There must also be enough room for the scan stage beneath the
cantilever; 30 x 30 x 20 mm clearance is required (WxDxH).
The conventional AFM can be used as normal either with the VideoAFM™ switched
off, or in conjunction with the VideoAFM™ when it is turned on.
<< back to top >>
10) Do you supply standard AFMs?
Infinitesima does not supply the conventional AFM, the VideoAFM™ is an
attachment designed to fit on a wide range of microscopes to enhance the user's
capabilities.
<< back to top >>
11) Is the VideoAFM™ an attachment to conventional AFM systems?
Yes.
<< back to top >>
12) Is the VideoAFM™ compatible with my existing AFM?
The VideoAFM™ is compatible with most AFMs.
Please contact your sales representative for further information.
<< back to top >>
13) Are the microscanners reuseable?
Infinitesima recommends using a new scanner with each new sample.
<< back to top >>
14) What do the consumables cost?
Please contact your sales representative for further information.
<< back to top >>
15) Does Infinitesima recommend a particular AFM system?
Infinitesima do not recommend a particular microscope. The VideoAFM™ is
designed to work with a wide range of systems, each with their own capabilities.
<< back to top >>
16) How much data is collected?
Working at 256 x 256 pixels (full data, no compression), the VideoAFM™ produces
movies with size of about 1 MB per second of recording. These can be burnt onto
DVD, put onto memory sticks or alternatively archived on the controller.
<< back to top >>
17) How much does it cost?
Please contact your sales representative for further information.
<< back to top >>
Modes of operation
1) Does the VideoAFM™ operate in contact mode?
When using the VideoAFM™, the conventional AFM is used in contact mode.
However, preconceptions about contact mode do not apply to the VideoAFM™. At
these much higher scan speeds, the tip/sample interaction time is greatly
reduced for specific points on the sample, dramatically changing the nature of the
interaction, so much softer samples are able to be imaged than on a conventional
AFM in contact mode.
Correspondingly, hard surfaces do not wear the tip down as in traditional slowscanning
contact mode.
<< back to top >>
2) Can I use the VideoAFM™ cantilever in tapping mode?
Yes, in liquid operation.
Please contact your sales representative for further information.
<< back to top >>
3) Is it calibrated? Can we use it for CD (critical dimension) metrology?
The VideoAFM™ is calibrated in the slow scan axis and can be self calibrated in
the facts scan by comparing features from traditionally AFM images or by moving
a specified distance using the conventional AFM. Ask our sales representative
for a demonstration.
<< back to top >>
4) How does the feedback work?
One of the factors limiting the maximum speed of operation of a conventional
AFM is the electronic feedback system. The VideoAFM™ overcomes this limitation
by removing the requirement for an electronic feedback system by utilising the
intrinsic mechanical properties of a specially designed and engineered cantilever
to enable the tip to track the surface of the sample at very high speed (greater
than 10 cm per second).
A constant force image is generated by applying a Direct Force™ to the tip of the
cantilever. The imaging force is controlled by adjusting the magnitude of the
Direct Force™. This is a key technology in enabling the video rate imaging and has
taken many years to perfect.
<< back to top >>
5) Does it use conventional cantilevers?
The VideoAFM™ uses specialist silicon nitride cantilevers that can be purchased in
packs of 10, 50 or 100.
<< back to top >>
6) Does it work in liquid? What are the differences?
Yes, the VideoAFM™ does work in liquid. Operation in liquid requires upgrade
package, which includes a liquid scan head, additional liquid module for
controller and a starter pack of consumables including liquid microscanners and
liquid VideoAFM™ levers.
<< back to top >>
7) Can you work at elevated temperatures? Do you supply a heating stage? What
temperatures can you work at?
The VideoAFM™ is designed to operate at ambient temperatures. However, we
have researches using the VideoAFM™ to observe polymer process presently at
temperatures up to ~ 80 deg C and have successfully imaged the surface of a
molten polymer crystallising.
Please contact Infinitesima for advice for operating the VideoAFM™ at elevated
temperatures.
<< back to top >>
8) The scan area is quite small. Is that a problem?
Maximum images size is about 3 microns square in air, but as the VideoAFM™ is
giving you a video rate image, you can simply move around much larger areas.
Also these images can be stitched together to create highly detailed images of
larger areas, all in a fraction of the time of conventional imaging.
<< back to top >>
9) What file formats and length of video can be collected?
The movies are saved in AVI file format, a standard that gives the VideoAFM™ the
most flexibility. The data can be reviewed as a movie or with any video editing
software. The movies remain uncompressed, so no data is lost due to encoding.
Video durations are only limited by the MS Windows file size limitations. You
would have to record a video for over an hour for this to be a problem. That's
over 50,000 images at 256 x 256 pixels!
<< back to top >>
Samples and sample preparartion
1) What surfaces can be imaged?
As with any AFM, the VideoAFM™ can image a wide variety of samples and with
the real-time direct force interaction, you can control your interaction with much
more delicate samples than might be assumed.
Commonly used samples are:
· Polymer films
· Biological samples, e.g. collagen, DNA
· Silicon structures
<< back to top >>
2) Can the VideoAFM™ measure soft samples like living cells or molecules?
Yes.
<< back to top >>
3) Can you use any standard cantilever with the VideoAFM™?
The VideoAFM™ uses special cantilevers.
<< back to top >>
4) Can the VideoAFM™ image DNA, proteins or antigens?
The VideoAFM™ is available with liquid operation. However, the usual sample
considerations must be taken into account as for ANY AFM technique. The
instrument has been used to image DNA in air, so it is possible to image
biological polymers. Infinitesima are currently working with a number of groups to
develop sample preparation and VideoAFM™ techniques for imaging biological
molecules in liquid.
<< back to top >>
5) Does fast scanning in contact mode damage soft samples?
The high tip velocity of the VideoAFM™ means that the tip/sample interaction is
different to conventional AFM. For example, Infinitesima have successfully
imaged the surface of a molten polymer. As for ANY AFM technique, high contact
forces and imaging for long periods of time can degrade samples.
<< back to top >>
6) What are the sample size limitations?
The sample size is limited by its mass which affects the resonant frequency
microscanner and in turn the speed of the VideoAFM™.
Infinitesima provides convenient sample mounting blocks with dimensions
0.8 x 0.8 x 0.6 mm.
Please contact your sales representative for further information.
<< back to top >>
|
|
